[2024-feb-29] Sad news: Eric Layton aka Nocturnal Slacker aka vtel57 passed away on Feb 26th, shortly after hospitalization. He was one of our Wiki's most prominent admins. He will be missed.
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
slackwarearm:inst_sa64_lx2160a_honeycomb [2024/03/11 16:23 (UTC)] – mozes | slackwarearm:inst_sa64_lx2160a_honeycomb [2024/05/13 11:35 (UTC)] – mozes | ||
---|---|---|---|
Line 59: | Line 59: | ||
^ SD Card | Gigastone 32GB Micro SD Card (UHS-I U1 A1 Class 10) | Great performance and mostly reliable | | ^ SD Card | Gigastone 32GB Micro SD Card (UHS-I U1 A1 Class 10) | Great performance and mostly reliable | | ||
^ USB Memory | SanDisk 16GB Cruzer USB 2.0 Flash Drive or similar | Stores installer image on first installation | | ^ USB Memory | SanDisk 16GB Cruzer USB 2.0 Flash Drive or similar | Stores installer image on first installation | | ||
- | ^ GPU (PCIe port) | AMD RX550 2GB GPU | works out of the box with Slackware ARM and has 1 DVI and 1 HDMI port. NVidia GPUs are not recommended. | + | ^ GPU (PCIe port) | AMD RX550 4GB GPU | works out of the box with Slackware ARM and has 1 DVI and 1 HDMI port. NVidia GPUs are not recommended. |
^ Monitor | Modern LCD or LED | Any monitor that uses HDMI or DVI inputs | | ^ Monitor | Modern LCD or LED | Any monitor that uses HDMI or DVI inputs | | ||
^ Network | Asix USB 3.0 to Ethernet adapter | It was reported some time ago that the On-board ethernet port does not work until kernel firmware is installed. | | ^ Network | Asix USB 3.0 to Ethernet adapter | It was reported some time ago that the On-board ethernet port does not work until kernel firmware is installed. | | ||
Line 246: | Line 246: | ||
<note warning> | <note warning> | ||
Skipping this process will leave your system in a state that is unsupported. | Skipping this process will leave your system in a state that is unsupported. | ||
+ | |||
===== Finishing Up the Installation ===== | ===== Finishing Up the Installation ===== | ||
The remaining installation steps initiated by the **setup** command are left up to the reader to answer. You will be asked to pick the services you want to activate, amongst other custom options. | The remaining installation steps initiated by the **setup** command are left up to the reader to answer. You will be asked to pick the services you want to activate, amongst other custom options. | ||
Line 261: | Line 262: | ||
< | < | ||
- | Remember to reconfigure | + | == HoneyComb LX2 Boot Configuration == |
+ | |||
+ | <note important> | ||
+ | |||
+ | The DIP switches need to be changed to make the SPI flash be the location from which the HoneyComb LX2 will boot its firmware. | ||
< | < | ||
{{: | {{: | ||
+ | == Configure the Firmware' | ||
+ | |||
+ | |||
+ | * Remove the USB thumb drive containing the Slackware Installer | ||
+ | * Power on the HoneyComb. | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | |||
+ | When you are prompted, press the **Escape** key (you may need to press it a couple of times): | ||
+ | |||
+ | Use the cursor keys to scroll down to 'Boot Maintenance Manager' | ||
+ | |||
+ | {{: | ||
+ | |||
+ | Press Enter on 'Boot Options' | ||
+ | |||
+ | {{: | ||
+ | |||
+ | Press Enter on ' | ||
+ | |||
+ | {{: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | Use the cursor keys within the menu to locate the block storage device on which you installed Slackware. | ||
+ | In this example it's a Kingston SSD: | ||
+ | |||
+ | {{: | ||
- | **TODO: screen shot** | + | Use the ' |
- | Remove the USB thumb drive and power on the Honeycomb. When you are prompted to hit the **Escape** key, do so. Enter the **Boot Maintenance Manager**. | + | {{: |
{{: | {{: |