[2024-feb-29] Sad news: Eric Layton aka Nocturnal Slacker aka vtel57 passed away on Feb 26th, shortly after hospitalization. He was one of our Wiki's most prominent admins. He will be missed.
Differences
This shows you the differences between two versions of the page.
Next revision | Previous revisionLast revisionBoth sides next revision | ||
howtos:hardware:arm:releases_14.2 [2018/11/14 08:44 (UTC)] – created mozes | howtos:hardware:arm:releases_14.2 [2021/12/16 11:22 (UTC)] – mozes | ||
---|---|---|---|
Line 2: | Line 2: | ||
====== Slackware ARM 14.2 ====== | ====== Slackware ARM 14.2 ====== | ||
- | Slackware ARM has commonly been referred to as the "soft float port" | + | === Supported Hardware Models === |
- | This is only important in so much as one is unable to perform an in-place upgrade from 14.2 to any newer release of Slackware due to: | + | |
- | * The ABI is incompatible with all newer releases. | + | |
- | * Support for the older armv5-only (such as " | + | |
- | The Soft Float port goes back to Slackware v11.0, but the " | + | The following Hardware Models have Direct Integration support (they are supported "out of the box"). |
- | Note: Slackware ARM 14.2 will cease to be maintained following the release of 15.0. | + | ^ Hardware model ^ ARM CPU type ^ Maintainer |
+ | | Trimslice | ||
+ | | Plug Computers | ||
+ | | ARM Versatile (emulated via QEMU) | armv5 | Stuart Winter < | ||
+ | | Banana Pi | armv7/ | ||
- | === Officially | + | === Extra-Slackware |
+ | The following Hardware Models do not have Direct Integration support (are not supported "out of the box"). | ||
+ | ^ Hardware model ^ ARM CPU type ^ Slackware version ^ | ||
+ | | Raspberry Pi 1 | armv6 | [[howtos: | ||
+ | | Raspberry Pi 2 | armv7/ | ||
+ | | Raspberry Pi 3 | armv8/ | ||
+ | | Toshiba AC100 | armv7/ | ||
+ | | Open Pandora | ||
+ | | LinuXino A10 Lime | armv7/A10 | [[http:// | ||
+ | | OLinuXino A10S Micro | armv7/A10S | [[http:// | ||
+ | | XZPAD700 (works on most Axx-based boards)| armv7/Axx | [[http:// | ||
+ | | OLinuXino iMX233 | armv5/ | ||
- | ^ Type of Supported ^ Hardware model ^ ARM CPU type ^ Slackware version ^ | + | If you're looking to get SlaXBMC on your ARM device you could start reading |
- | | Official | Trimslice | + | |
- | | Official | Plug Computers | armv5/ | + | |
- | | Official | ARM Versatile (emulated via QEMU) | armv5 | [[ftp:// | + | |
- | | Official | Banana Pi | armv7/ | + | |
- | === Community Supported Hardware === | ||
- | |||
- | |||
- | ^ Type of Supported ^ Hardware model ^ ARM CPU type ^ Slackware version ^ | ||
- | | Community | Raspberry Pi 1 | armv6 | [[howtos: | ||
- | | Community | Raspberry Pi 2 | armv7/ | ||
- | | Community | Raspberry Pi 3 | armv8/ | ||
- | | Community | HummingBoard | ||
- | | Community | Toshiba AC100 | armv7/ | ||
- | | Community | Open Pandora | ||
- | | Community | OLinuXino A10 Lime | armv7/A10 | [[http:// | ||
- | | Community | OLinuXino A10S Micro | armv7/A10S | [[http:// | ||
- | | Community | XZPAD700 (works on most Axx-based boards)| armv7/Axx | [[http:// | ||
- | | Community | OLinuXino iMX233 | armv5/ | ||