28-mar-2016: Welcome to our new server! Faster and less prone to crashing.
Add this page to your book
Remove this page from your book
Table of Contents
Hibernation (also known as suspend-to-disk) is a method used to power down a computer while preserving the state of the operating system. Once powered up, the operating system will be in the exact state as it was at the time of hibernation.
In Slackware, hibernation works out-of-the-box. However, in order to resume successfully from a hibernated state, you need to configure the bootloader so it knows where to locate the resume data.
KDE, XFCE and other desktop environments offer hibernation from logout screen/menu.
Lightweight Window Managers
You can hibernate your system from console. Either as root via pm-utils or D-Bus with additional programs as regular user.
Hibernation is done via
Slackware offers two services to control power management in it's recent releases. UPower and HAL. Since HAL is deprecated in Slackware 14.0, use HAL in older Slackware releases (from 12.0 to 13.37), otherwise use UPower.
Use one of these command to hibernate your system.
$ dbus-send --system --print-reply --dest="org.freedesktop.UPower" \ /org/freedesktop/UPower org.freedesktop.UPower.Hibernate
$ dbus-send --system --print-reply --dest="org.freedesktop.Hal" \ /org/freedesktop/Hal/devices/computer org.freedesktop.Hal.Device.SystemPowerManagement.Hibernate
Booting from LVM
LILO doesn't support booting from LVM, therefore you have to create initial ramdisk (initrd). You need one even though your kernel has build-in support for LVM.
You don't have to specially adjust
lilo.conf because you can set everything resume-related in initrd.
mkinitrd -c -k <kernel-version> -f <fs_type> -m <modules_required_to_boot> -r <root_partition> -h /dev/volumegroup/swap -L
- -h set your hibernation/swap logical volume
- -L activate LVM
Next step is to make sure your
lilo.conf contains following snippet
image = /boot/vmlinuz root = /dev/sdaX initrd = /boot/initrd.gz label = Slackware read-only # Partitions should be mounted read-only
If you don't use LVM, you can simply tell kernel where to resume from by adding append line:
/dev/sdaX with your actual swap partition.
lilo to save changes.
Lock your computer upon resuming
You may have noticed that when your computer resumes, there is no protection to ensure no one can use your computer. As
pm-hibernate must be run as root, any user that powers up your computer will be granted a root terminal! I'll show you some tricks to ensure a proper lock of the system.
From the command line
If you dont have an X session open, the only way to lock your computer is to logout from your session before hibernation. You can use the following command:
pm-hibernate & logout (OR pm-hibernate & exit)
It's important to logout from every tty prior to hibernation!
logout will only log you out from the terminal from where you launched the command. Please read the warning in the following section.
logoutmay not have enough time to complete. You may think that using
&could do the trick (as it will log out the user after resuming), but it allows the user doing a CTRL+Ctrl upon resuming, killing the
From an X session
If you want to lock the computer prior hibernation, you can issue the following command (as root of course):
# xlock & sleep 5 ; pm-hibernate
You can also create the following script:
#!/bin/bash echo 'Hibernating in 5 seconds' xlock & sleep 5 pm-hibernate
xlock is a command that locks your X session. Upon rebooting, you will be asked for the root password. The
sleep command may be omitted, but I think it's safer to leave it, so you are sure that
xlock has enough time to run properly. You don't have to use
logout) at the end of the command or the script, as it has no use concerning security. You may want to use it though to automatically close the xterm on resuming.
xlockcan be killed, leaving full access to the X session.
For people using init3 (no automatic X startup), remember to also logout from the tty from where you launched the X system with
startx: hit CTRL+Z (to suspend the task), then
bg(to resume the task in the background), then CTRL+D (or
logout) to logout.
If one is a sudoer, ie, can use sudo, then the following can also be used:
- Hibernate to encrypted swap - README_CRYPT.TXT